Hp procurve service unsupported transceiver

Hp procurve service unsupported transceiver

An unsupported transceiver module has been installed in the transceiver slot. The HP ProCurve Switch 2224 supports installation of only the HP Advancestack 100Base-FX Transceiver Module (product number J3193B). Been looking around for a while to see if there is a compatible Bidi SFP+ (10gig) transceiver for HP Procurve switches. Right now, we lease two strands of fiber to a remote facility for a 10-gig link-up, however hoping to reduce the possibility of a single point of failure and have a 10-gig link to each switch. I have a couple of J4903 2824 24-Port Procurve switches, which have 1Gb fibre gbic modules installed. I *think* the gbic modules are J4858C but I'm not certain, I can't see any way of telling through the web interface what model of gbic module is installed.

(2) Supported transceivers:As of this printing the following HPE ProCurve transceivers are supported by the HPE ProCurve 2-Port 10-GbE SFP+ al Module: HPE ProCurve SFP+ SR transceiver (J9150A) HPE ProCurve SFP+ LR transceiver (J9151A) HPE ProCurve SFP+ LRM transceiver (J9152A) HPE ProCurve 10-GbE SFP+ 1 m Direct Attach Cable (J9281A) HP 5 year 6 hour CTR ProCurve Chassis6 Hardware Support Legal Disclaimer Information published on this site may refer to products, programs or services that are not available in your country. n.b On Cisco platforms the command "service unsupported-transceiver" is generally available in NxOS and IOS versions. The command won't autocomplete and, as is implied, it is unsupported but allows the use of 3rd party optics. – rnxrx Sep 15 '12 at 0:37

Hi, I have a switch HP E5406 J8697A, I integrated a module HP 24p SFP V2 J9537A. I want to set transceivers D-Link or Huawei in this switch but I got unsupported transceiver. I need to update those transceivers to be supported by the switch (like allow-unsupported-transceiver, upgrade version, etc..... You can get a device to give the SFP eeprom the correct vendor code, but last time I checked they were expensive. I'm not aware of a HP equivalent to Cisco's service unsupported-transceiver. Is it bringing the link up (i.e just whining in the logs) or is it simply refusing to work? Hotline: (+852) 2410 8131 between 0900 - 1800 HKT . Aspen Optics Ltd. Unit 1504, Chevalier Commercial Center, 8 Wang Hoi Road, Kowloon Bay, Hong Kong

HP ProCurve High-Speed Transceivers Installation Guide Introduction The HP ProCurve High-Speed Transceivers can be installed into a number of HP ProCurve networking devices to provide 100 Mbps and 1000 Mbps connections to other compatible network devices. This document describes how to install, verify, and troubleshoot the following HP ProCurve ... J9084A ProCurve NAC El Startup Service (802.1x) 4/1/2010 J9342A HP ProCurve MSM323-R US Access Point 4/1/2010 ... J4864A HP ProCurve Switch gl Transceiver Module 10/1 ... Nov 15, 2016 · The 16.02 release for the ArubaOS-Switch (Provision) wired switches includes a welcome ‘new’ feature to enable the use of unsupported transceivers. Previously, the switches were simply blocking the use of 3th party transceivers. With this new command, the admin can override this behavior. Introduction : A Small Form-factor Pluggable (SFP) module is a compact, hot-pluggable transceiver used for both telecommunication and data communications applications. Diagnostic information related to signal strength, temperature, etc can be polled from SFPs installed in the Mobility Access Switch....

Hotline: (+852) 2410 8131 between 0900 - 1800 HKT . Aspen Optics Ltd. Unit 1504, Chevalier Commercial Center, 8 Wang Hoi Road, Kowloon Bay, Hong Kong Re: Command service unsupported-transceiver Yes, it's undocumented as it's one of Cisco's "hidden" commands. What it did on earlier IOSs, it allowed non-Cisco transceivers to be used. Without it, the IOS would disable the port if a non-Cisco transceiver was plugged into the port. HP ProCurve Switch 2224 (HP J4095A) Disclaimer The information contained in this document is subject to change without notice. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not HP ProCurve Switch 6200yl-24G-mGBIC J8992A Introduction The HP ProCurve Switch 6200yl-24G-mGBIC is an advanced Layer 3 stackable switch in 1U height. It has 24 mini-GBIC slots and an expansion slot for an optional 4-port 10-GbE module. Designed to be deployed as an aggregator of traffic from the edge to

n.b On Cisco platforms the command "service unsupported-transceiver" is generally available in NxOS and IOS versions. The command won't autocomplete and, as is implied, it is unsupported but allows the use of 3rd party optics. – rnxrx Sep 15 '12 at 0:37 Hi there, My home service provider delivers fibre optic to my home with a gateway of their own. I went to plug in the SFP provided to my HP ProCurve 2520G-PoE J9299A switch and I get "Unsupported SFP" I've seen similar errors with cisco, gear but have found work arounds. I've tried all that I can, i...

Port 23 Transceiver type not supported in this port. The serial numbers are valid J9150A serial but these SFP+ are normally known as HP ProCurve 10-GbE SFP+ SR Transceiver (J9150A) Part Number 1990-3878 as can be seen, the part number differs. The latest firmware version W.14.49 has been applied and the problem still persists. Hi, I have a switch HP E5406 J8697A, I integrated a module HP 24p SFP V2 J9537A. I want to set transceivers D-Link or Huawei in this switch but I got unsupported transceiver. I need to update those transceivers to be supported by the switch (like allow-unsupported-transceiver, upgrade version, etc..... product, see the document titled “Support for the HP ProCurve BX Transceivers” on the “ProCurve Mini-GBICs and SFPs” Manuals Web page. The J9142B connects to the J9143B “upstream” transceiver, or to any IEEE-standard 1000BASE-BX10-U (“upstream”) device. (A 1000-BX-D transceiver can only connect to a 1000-BX-U product. J9084A ProCurve NAC El Startup Service (802.1x) 4/1/2010 J9342A HP ProCurve MSM323-R US Access Point 4/1/2010 ... J4864A HP ProCurve Switch gl Transceiver Module 10/1 ...

regarding the "service unsupported-transceiver" command I learnt the following. This command is intended as a last-resort to try to use a third party Optic product to work with Cisco devices. Cisco does not gurantee the working of the third party module with this command. If you

Feb 20, 2015 · Hi Spiceworks community, I'm looking to see if there's anyone out there that's had luck with forcing optical transceivers to be accepted by switches that don't want to use non-branded parts. Specifically, we have a pair of IBM RackSwitch G8264 units, and we're trying to use a 100-meter AOC (Active Optical Cable) with Emcore branded transceivers. HP 5 year 6 hour CTR ProCurve 5212zl Hardware Support Legal Disclaimer Information published on this site may refer to products, programs or services that are not available in your country. Apr 11, 2013 · service unsupported-transceiver. If you issue this command you'll get the following warning: " Warning: When Cisco determines that a fault or defect can be traced to the use of third-party transceivers installed by a customer or reseller, then, at Cisco's discretion, Cisco may withhold support under warranty or a Cisco SFPEX offers a full range of compatible HP transceivers. Order high quality HP optical transceivers at SFPEX.com with life time warranty.

It is possible to force the switch to try using the third party SFPs using the global configuration command service unsupported-transceiver (needs to be written precisely as indicated here without abbreviations or command completions as it is a hidden command). Whether the SFP will work successfully depends but usually, my experience was positive. I have a couple of J4903 2824 24-Port Procurve switches, which have 1Gb fibre gbic modules installed. I *think* the gbic modules are J4858C but I'm not certain, I can't see any way of telling through the web interface what model of gbic module is installed.

Hotline: (+852) 2410 8131 between 0900 - 1800 HKT . Aspen Optics Ltd. Unit 1504, Chevalier Commercial Center, 8 Wang Hoi Road, Kowloon Bay, Hong Kong Nov 15, 2016 · The 16.02 release for the ArubaOS-Switch (Provision) wired switches includes a welcome ‘new’ feature to enable the use of unsupported transceivers. Previously, the switches were simply blocking the use of 3th party transceivers. With this new command, the admin can override this behavior. Find many great new & used options and get the best deals for Hewlett Packard ProCurve (J9151A) (884420143314) 10240 Mbps Transceiver at the best online prices at eBay! Free shipping for many products! I have a couple of J4903 2824 24-Port Procurve switches, which have 1Gb fibre gbic modules installed. I *think* the gbic modules are J4858C but I'm not certain, I can't see any way of telling through the web interface what model of gbic module is installed.

by Hewlett-Packard. Warranty See the Customer Support/Warranty booklet included with the product. A copy of the specific warranty terms applicable to your Hewlett-Packard products and replacement parts can be obtained from your HP Sales and Service Office or authorized dealer. Safety Before installing and operating these products, please read HP ProCurve Switch 2500 Series The HP ProCurve Switch 2500 Series consists of Layer 2 managed 12- and 24-port switches. The switches include two Gigabit transceiver slots for copper or fiber connectivity, including 100Base-FX. The 2512 and 2534 switches have a proven track record of reliability and feature an industry-leading warranty and next-day View and Download HP PROCURVE 6120 management and configuration manual online. ProCurve Series 6120 Switches. PROCURVE 6120 Switch pdf manual download. Also for: Procurve 6120g/xg, Procurve 6120xg.